The key to locking valves

Ball valves, gate valves, plug valves... choosing the right locking device can seem a difficult decision. But, in fact, answering a few questions will he

Valves come in a wide range of shapes and sizes. Choosing the right locking device can seem a challenging task. But it does not have to be – it is possible to filter out the right product by answering a few basic questions. No special knowledge about the specification or performance of the valve is needed. Whether you have ball valves, gate valves, plug valves, globe valves or butterfly valves, there are two factors that determine what type of locking device is needed. These are the method of operation followed by the size of the valve. Many valves are manually operated via a hand wheel, lever (wrench) or sometimes the valve might be power actuated – electric motor, hydraulic or pneumatic actuator for instance. Regardless of the method of operation, all valves can be locked out in some way. Challenging For manual, wheel operated valves you can used a wheel lockout device, similar to those manufactured by Master Lock or Brady. They are designed to encapsulate the wheel of the valve thereby blocking access to the wheel and preventing operation. They come in a range of five sizes; the largest can cover a wheel of 350mm diameter. The wheel cover is secured in place using a safety padlock. Users can choose between four different colours to denote the process medium or perhaps the valve positional status. If the valve wheel you need to lock is larger than 350mm, you can consider a cable lockout or padlock and chain. These work by threading the cable or chain around the rim of the valve and through the bonnet or perhaps a piece of adjacent pipe work or steel work. Locking a lever operated valve can be slightly more challenging. The problem with lever operated valves (ball valve, plug valve, butterfly valve) is that they vary greatly from one manufacturer to another. The topworks design of the valve is rarely the same and this means that the locking device may not engage securely on the valve. To resolve this, Master Lock has developed an innovative lockout known as the Seal Tight valve lockout. It works by removing the valve lever and locking it away in a pouch which is wrapped around the body of the valve. Some valve locking devices can only lock the valve in a single position, usually the closed position. Other valve lever lockouts work by attaching to the lever and physically blocking the turning movement of the valve. If your valve is actuated, locking it off can actually be quite straightforward. For an electrical actuator, the device will have an on/off switch on board. The switch often has a padlock facility that can be used to secure the switch in the “off” position. For pneumatic or hydraulic actuated valves, blocking the flow of air or oil to the actuator will disable it. This can be done with a small diameter ball valve in the flow line. This valve can then be locked out with one of the lever locking devices described above. On a note of caution, changing the operational function of actuated valves in this way should only be done in consultation with qualified process engineers. Protection At the start of this article we stated that there are two factors that determine which type of locking device is needed. However, you might like to also consider a third factor. That is the degree of protection against inadvertent operation. Inadvertent operation could be regarded as accidental operation, deliberate procedural violation or vandalism. If the location of the valve makes it a target for vandalism, this must be taken into consideration. In this scenario, a risk assessment should be undertaken. If the consequences present a risk of injury or death, then a high integrity locking device is needed. Equally, if the consequences of operation could result in a high cost loss, these circumstances may also lead you to consider a high integrity locking device. So what is meant by a high-integrity locking device? This type of device, (normally referred to as an interlock) is very difficult to remove from the valve in as much as specialist tools would probably be needed. It would also be highly tolerant to abuse and attempts to defeat or override. The device can be locked in both open and closed positions with a separate key corresponding to each locked position. Valve interlocks are often used in a set of multiple valve locks whereby the sequence of operation of a number of valves can be pre-determined through the coding of the keys. So whether you are simply locking off a valve during a maintenance procedure or implementing sequential control over a number of valves, there is a suitable device available. www.totallockout.com

Tags



Topics


Click a keyword to see more stories on that topic, view related news, or find more related items.

Comments

You need to be logged in to make a comment. Don't have an account? Set one up right now in seconds!


© Faversham House Group Ltd 2010. edie news articles may be copied or forwarded for individual use only. No other reproduction or distribution is permitted without prior written consent.